We've found the article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and thought it made sense to discuss it with you on this site.
Setting up a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a new one is also a reasonably difficult job. If the old tub is conveniently accessible, the task can move immediately; if you have to open up a wall to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to leave the old bathtub and set in the brand-new one. Ensure you have certified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually currently bought a new bathtub and also do not require to change the plan of your previous water pipes.
Your tools as well as product list should comprise the following:
- New Bath tub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipe Caps
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to avoid pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and also examine the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub needs to wait up until the bath tub has been used a minimum of once as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing difficulties with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Try to leave a remark down the page. We'd be delighted to listen to your feelings about this blog post. In hopes that you come back again before long. Loved our blog posting? Please share it. Help others find it. Thank-you for taking the time to read it.
Book Today!
Comments on “Just How to Install a Bathtub Yourself: Removing and also Replacing.”